JSON output canīe obtained by appending ‘json’ at the end. Shows the routes which are redistributed by the router. JSON output can be obtained by appending “json” at the end. Shows state about what is being redistributed between zebra and OSPF6. This command shows internal routing table. JSON output can be obtained by appending “json” at the Shows counts of different packets that have been recieved and transmittedīy the interfaces. Shows state and chosen (Backup) DR of neighbor. To see OSPF interface configuration like costs. All the other filters are applicable here as well. This command is used to filter the LSAs which are originated by the present show ipv6 ospf6 database self-originated ¶ JSON output can be obtained byĪppending ‘json’ to the end of command. We can use the LSA type filter and views with The LSAs additinally can also be filtered with the linkstate-id andĪdvertising-router fields. show ipv6 ospf6 database adv-router A.B.C.D linkstate-id A.B.C.D ¶ JSON output can be obtained by appending ‘json’ to theĮnd of command. These options filters out the LSA based on its type. JSON outputĬan be obtained by appending ‘json’ to the end of command. These options helps in viewing all the parameters of the LSAs.
This command shows LSAs present in the LSDB. JSON output can be obtained by appending ‘json’ Show information on a variety of general OSPFv3 and area state andĬonfiguration information. Showing OSPF6 information ¶ show ipv6 ospf6 ¶ Metric values and route-map can also be specified optionally. The alwaysĪrgument injects the default route regardless of it being present in the The command injects default route in the connected areas. Redistribute routes from other protocols into OSPFv3. Redistribute routes to OSPF6 ¶ redistribute ¶ Substract a metric value from an existing metric. To add a metric value to an existing metric.
Set a metric for matched route when sending announcement. Set explicitly network type for specified interface. ipv6 ospf6 network (broadcast|point-to-point) ¶ ipv6 ospf6 transmit-delay TRANSMITDELAY ¶ ipv6 ospf6 retransmit-interval RETRANSMITINTERVAL ¶ Default 10 ipv6 ospf6 dead-interval DEADINTERVAL ¶ ipv6 ospf6 hello-interval HELLOINTERVAL ¶ Default value depends on the interfaceīandwidth and on the auto-cost reference bandwidth. OSPF6 interface ¶ ipv6 ospf6 area ¶Įnable OSPFv3 on the interface and add it to the specified area. The not-advertise option, when present, prevents the summary route fromīeing advertised, effectively filtering the summarized routes. This command can only be used at the area boundary (ABR router).īy default, the metric of the summary route is calculated as the highest Summarize a group of internal subnets into a single Inter-Area-Prefix LSA. Use this command to control the maximum number of parallel routes that This configuration setting MUST be consistent across all routers This sets the reference bandwidth for cost calculations, where thisīandwidth is considered equivalent to an OSPF cost of 1, specified in Time an SPF-triggering event occurs within the hold-time of the previous Separated by between 400ms to 10s, the hold-time increasing by 400ms each Further consecutive SPF calculations will always be Least 200ms between an event which requires SPF calculation and the actual To 400ms and the maximum holdtime to 10s. In this example, the delay is set to 200ms, the initial holdtime is set The current holdtime is reset to the initial-holdtime. Hold-time elapses without any SPF-triggering event occurring then Will cause the holdtime to be increased by initial-holdtime, boundedīy the maximum-holdtime configured with this command. Set to the initial-holdtime configured with the above command.Įvents which occur within the holdtime of the previous SPF calculation The hold-time is adaptive and initially is The delay specifies the minimum amount of time to delay SPFĬalculation (hence it affects how long SPF calculation is delayed afterĪn event which occurs outside of the holdtime of any previous SPFĬalculation, and also serves as a minimum holdtime).Ĭonsecutive SPF calculations will always be separated by at least Milliseconds and must be in the range of 0 to 600000 milliseconds.
This command sets the initial delay, the initial-holdtimeĪnd the maximum-holdtime between when SPF is calculated and theĮvent which triggered the calculation. OSPF6 router ¶ router ospf6 ¶ ospf6 router-id A.B.C.D ¶ Ospf6d is a daemon support OSPF version 3 for IPv6 network.
0 kommentar(er)
